YardPour

Floor leveler · bags & coverage

Self-Leveling Concrete Calculator

This self-leveling concrete calculator turns room size and average depth into cubic feet and bag counts for cement-based floor leveler. Yield per bag is editable—use the figure on your product's data sheet. For what self-leveler is, how to prime and pour, and product thickness limits, see the self-leveling concrete guide. For a full structural slab, use the concrete slab calculator or the main concrete calculator.

Updated Free · no sign-up · inputs stay in your browser

Floor and depth

ft
ft
in
Grid the room; average high and low spots.
Bag yield (editable)
ft³
%
lb

Bags to buy (rounded up)

1150 lb bags

200 ft² × 0.25 in = 4.17 ft³ net

Order volume
4.58 ft³
Cu yd (order)
0.17
Sq ft per bag at this depth
21.6
ft³ = area × (depth in ÷ 12) bags = ⌈ order ft³ ÷ yield ⌉ area 200 × 0.25/12 = 4.17 ft³

How much self-leveling concrete do I need?

Multiply the floor area in square feet by the average depth in feet to get cubic feet, then divide by the wet yield per bag and round up. Example: 200 sq ft at 1/4 in (0.0208 ft) is 200 × 0.0208 = 4.17 ft³. At 0.45 ft³ per 50 lb bag that is about 10 bags before waste. Depth must be an average—self-leveler fills lows, not just the nominal thickness of the whole room.

Measuring average depth on an uneven floor

Mark a grid every 4 to 6 feet. At each point, measure from a taut string or laser line down to the low spot. Average those depths, or split the room into zones if one corner is much deeper and run the calculator twice. Deep pockets over about 1 inch often need repair mortar first; most self-levelers have a per-layer maximum in the manufacturer's sheet.

Coverage per bag by depth

Manufacturers usually cite coverage at one reference depth. QUIKRETE Self-Leveling Floor Resurfacer (1249-50) lists about 21 sq ft per 50 lb bag at 1/4 inch. Double the depth and you halve the area per bag. Enter your label yield in the tool above instead of trusting a generic default.

Planning coverage scaled from QUIKRETE 1249-50 at 21 ft² per bag @ ¼ in
Average depthSq ft per 50 lb bag (approx.)
1/8 in42
1/4 in21
3/8 in14
1/2 in10.5

Minimum and maximum pour thickness

Limits are product-specific. the QUIKRETE Self-Leveling Floor Resurfacer data sheet allows feather edge up to 5/8 inch per layer, and deeper areas are built up in additional layers of no more than 5/8 inch each. Other products list different limits, so read the technical data sheet for the bag you actually buy.

How much self-leveling compound do I need for a room?

For a typical 1/4 inch skim, plan on one 50 lb bag per 21 sq ft, so a 10 × 12 ft bedroom takes about 6 bags and a 20 × 20 ft basement about 19 bags before waste. The table scales the QUIKRETE 1249-50 yield of 0.45 ft³ per bag to other room sizes and depths. Counts are rounded up to whole bags with no waste added; add 5–10% for a rough slab.

50 lb bags of self-leveler by room size and average depth (0.45 ft³ per bag)
RoomArea1/8 in1/4 in3/8 in1/2 in
Half bath (5 × 8 ft)40 sq ft1234
Laundry room (8 × 10 ft)80 sq ft2468
Bedroom (10 × 12 ft)120 sq ft36912
Kitchen (12 × 15 ft)180 sq ft591317
Living room (15 × 20 ft)300 sq ft7142128
Basement (20 × 20 ft)400 sq ft10192838

Worked example: a floor that needs two layers

  1. A 12 × 15 ft kitchen is flat except for a 4 × 6 ft dip that is 1 in deep at its center and averages 0.75 in.
  2. The QUIKRETE resurfacer allows 5/8 in per layer, so the dip is filled first: 24 sq ft × 0.75 in ÷ 12 = 1.5 ft³, about 4 bags.
  3. Then the whole room gets a 1/4 in skim: 180 sq ft × 0.25 ÷ 12 = 3.75 ft³, or 9 bags.
  4. Total 13 bags; buy 14 so the second pour is never short. Prime again between layers as the data sheet directs.

How much primer to mix

For its resurfacer, QUIKRETE specifies a primer of 1 part Concrete Bonding Adhesive (No. 9902) to 2 parts water, brushed or sprayed to an even coat with no puddles, and two coats on old, very porous concrete. Primer does not add volume, so it does not change the bag count above.

Primer, edges and feathering

Self-levelers require primer so the slab does not pull water from the mix. Dam doorways so fluid does not escape, and plan a continuous pour—working time is often well under 30 minutes. Feathering at edges is fine where the product allows a feather-edge minimum.

Self-leveler vs slab leveling

Self-leveling underlayment flattens a sound slab before flooring. If the slab has sunk or rocks, that is concrete leveling (mudjacking, foam, or grinding)—not a topping pour. Lifting a sunken slab instead? Read that guide. Pouring a new level surface on a stable base? You are in the right place.

Sources

Checked October 11, 2026.

Frequently asked questions

How many bags of self-leveling concrete for 100 square feet?

At 1/4 inch average depth, 100 sq ft is about 2.1 cubic feet. Divide by your bag yield (many 50 lb bags list about 0.45 ft³) and round up; QUIKRETE 1249-50 cites roughly 21 sq ft per bag at 1/4 inch.

How much floor leveler do I need?

Multiply floor area in square feet by average depth in feet for cubic feet, then divide by the yield printed on your bag. Add waste and round up to whole bags.

Does primer change how much self-leveler I need?

No. Primer does not change volume. It improves bond so you do not lose material to pinholes or dry slab suction.

How many bags of self-leveler do I need for 200 square feet?

At 1/4 inch average depth, 200 sq ft is 4.17 ft³. At 0.45 ft³ per 50 lb bag that is 9.3, so 10 bags before waste. At 1/8 inch it is 5 bags; at 1/2 inch, 19 bags.